Level 4 vs Level 5 Plasterboard Finish: Which Does Your Home Need?

Level 4 is the standard plasterboard finish and suits most rooms in most New Zealand homes. Level 5 adds a coating over the entire wall or ceiling surface, and it is worth specifying where strong light, dark colours or gloss paint would otherwise show every joint. The choice has to be made before the plasterboard goes up, and it has to be written into your quote. That is much easier when one team manages the framer, plasterer and painter, which is how we run renovations at Sorted Home Solutions.
This guide is about the finish on walls and ceilings (the “level of finish” for plasterboard, often called GIB stopping in Auckland). It is not about education qualification levels, which share the same numbers.
TL;DR
Level 4 is the default finish for plasterboard that will be painted normally. Most homes are prepared to Level 4.
Level 5 adds a coating over the full surface and tighter framing tolerances. It suits gloss or semi-gloss paint, dark colours and strong side lighting.
A Level 4 wall that is skim-coated later is not the same as Level 5. Level 5 has to be planned from the start.
Even a correct Level 5 minimises imperfections rather than hiding every one, so lighting and paint choice matter as much as the level.
Get the level written into your quote, along with who does the sanding, the clean-up and the paint system.
Table of Contents
What the two levels mean
New Zealand and Australia share a standard for finishing plasterboard, AS/NZS 2589. It sets out several levels of finish. For homes, the two that matter are Level 4 and Level 5.
According to Dulux’s technical advice, Level 4 is the standard finish where normal painting is carried out. Level 5 is the highest level, for a surface as free as possible from defects and visual blemishes. Dulux is clear that Level 5 does not mean a surface with no variation at all.
A Dulux technical document on levels of finish adds that most domestic and commercial buildings are prepared to Level 4.
Side by side
Level 4 | Level 5 | |
Role | Standard finish for normally painted surfaces | Highest level, for demanding surfaces |
Joints | Tape and three coats of jointing compound | The same, plus back-blocking of all joints in walls and ceilings |
Full-surface coating | Not required | Required, by skim coat or specialty surfacer |
Framing | Normal tolerances | Tighter tolerances under AS/NZS 2589 |
Suits | Flat or low-sheen paint, light textures, wallcoverings, ordinary lighting | Gloss, semi-gloss or non-textured paint, critical lighting, feature walls |
Who must cooperate | Stopper and painter | Framer, board installer, plasterer and painter |
What Level 4 involves
GIB’s trade article on achieving a Level 4 or 5 finish describes Level 4 as a three-coat joint system. Tape is bedded into the joint with the base coat. A second coat follows, typically 170 mm wide. The final coat is no less than 250 mm wide on tapered joints, or 500 mm on butt joints (where two cut ends meet). The joint build must not exceed 2 mm without forming a peak.

The result is a flat, paint-ready surface. For a bedroom, hallway or living room with flat or low-sheen paint and ordinary lighting, it is the right finish.
What Level 5 adds
The same GIB article says Level 5 requires everything in Level 4, plus three things:
Tighter framing tolerances. The timber behind the board has to be straighter, because a coating cannot straighten an uneven wall.
Back-blocking. All joints in walls and ceilings are supported from behind so the board does not flex at the joint.
A coating over the entire surface. An air-drying compound is applied by spray, roller or trowel.
Dulux gives two ways to do the final step. One is a plaster skim applied by a plasterer and finely sanded. The other is a specialty plasterboard surfacer, applied by spray or roller to a high film thickness and sanded before painting.
Why the coating matters
The full-surface coat is there to even out porosity. Joint compound and the paper face of the board absorb paint differently, and that difference shows up as dull or shiny patches (sometimes called flashing). GIB explains that the skim coat’s purpose is to remove this difference, not to flatten the surface.
It also explains why you cannot simply skim a Level 4 wall afterwards and call it Level 5. Dulux states that a Level 4 finish skim-coated later is not equivalent to Level 5, because Level 5 must be specified and installed from the start with its full set of requirements.
How light, colour and sheen change what you see
The level of finish is only half of the picture. The other half is how the finished wall is lit and painted.
Resene’s guide to levels of finish explains several things worth knowing:
Defects show up more clearly on ceilings than on walls.
Lighter colours hide imperfections better than dark ones.
Textured or flat finishes help disguise imperfections under critical light.
Rolling the paint, which leaves a slight orange-peel texture, also helps.
Dulux advises that where a Level 4 surface will be exposed to critical lighting, wallcoverings or textured coatings should be considered. Level 5 is needed where low-angle glancing light or spotlights combine with higher-sheen paint or darker colours, typically on a feature wall.
Common situations at home
Large windows and a long hallway wall. Daylight raking along the wall is the classic way joints appear.
Downlights close to a wall. Light skimming the surface exaggerates every ridge. Our downlight spacing guide shows how layout affects this.
Dark feature wall with semi-gloss paint. This is the case where Level 5 earns its cost.
Kitchens and bathrooms. These often use harder-wearing, higher-sheen paint. Our guides to low sheen walls in kitchens and paint finishes for bathrooms cover which sheen suits which room.
GIB is honest about the limits. It notes that even a good Level 5 finish can reveal imperfections under critical light. If that happens, the lighting should be changed or a different finish, such as solid polished plaster, used. Siniat’s installation guidance makes the same point: Level 5 minimises surface deviations rather than concealing all of them. That is why you should settle the paint colour and sheen at the same time as the finish level.
Which level for which room
Resene’s guide says Level 4 suits light textures, wallcoverings, economy-focused work and flat or low-sheen paint in non-critical light. Level 5 suits gloss, semi-gloss, low-sheen or non-textured flat paints, or where critical light exists. Elephant Plasterboard’s installation guide puts it the same way and notes that a skim coat would not normally exceed 1 mm finished thickness.
For a homeowner, that translates into a simple rule of thumb:
Situation | Likely choice |
Bedrooms, wardrobes, garage-to-house walls, typical living areas with flat paint | Level 4 |
Rooms with textured paint or wallcoverings | Level 4 |
Walls with large windows or strong raking light and a low-sheen or flat light colour | Level 4 is usually enough, discuss it with your plasterer |
Feature wall in a dark colour with a sheen | Level 5 |
Ceilings with downlights and semi-gloss paint | Level 5 |
Open-plan living with glossy finishes and lots of glass | Level 5 on the walls that catch the light |
You do not need to choose one level for the whole house. Level 5 can apply to the walls that need it, and Level 4 to the rest. Paying for Level 5 everywhere is the most common way to spend money with no visible result.
Decide before the board goes up
The Dulux technical document says the finish level should be decided at the design stage, and that leaving it until decoration after installation “may not produce the desired outcome”. GIB’s 2025 Site Guide introduction cautions that Level 5 is difficult to achieve and always needs cooperation between the framer, plasterboard installer and other trades.
That has a practical consequence. If the framer does not know a wall is going to Level 5, the framing tolerance will not be tight enough. If the board installer does not know, the joints will not be back-blocked. By the time the plasterer arrives, the opportunity has passed.
The same logic applies to estimating. A quote that treats plastering as one line, without the level of finish, cannot be compared fairly with another. If you want to see how tradespeople measure and price wall and ceiling areas, this walkthrough of drywall takeoff basics shows why the scope has to be agreed before pricing.

How the level changes your quote
Level 5 costs more because it adds a full coating, extra sanding, tighter framing and more coordination. It is a per-square-metre effect, so a large wall of glass-side plasterboard costs far more to upgrade than a small feature wall. We explain how this plays out locally in our guide to Auckland GIB stopping costs and why Level 4 vs 5 changes your quote.
Two things to keep in mind when you compare quotes:
Specifying Level 5 where Level 4 is enough adds cost with no visible benefit.
Under-specifying a gloss feature wall exposes every imperfection once the paint dries.
Prices published online by plastering businesses vary widely with the job, so use them only to get a feel. Your own written quote, for your own walls, is the figure that counts.
What to get in writing and how to check the result
When a plastering or renovation quote arrives, check that it states:
The finish level for each area, written as Level 4 or Level 5, not just “skim” or “stop”.
Whether framing and back-blocking are included if Level 5 is specified.
Who does the sanding, dust control and clean-up.
The paint system. Dulux recommends a three-coat system, one prepcoat and two topcoats, as set out in AS/NZS 2311:2009, over a surface that has been vacuumed, wiped and sealed with an acrylic sealer or undercoat.
What happens to defects that appear after the first coat of paint.
Checking the finish at handover
GIB says finish quality should be assessed at handover from stopper to painter, and that a sealer coat helps to highlight imperfections. The accepted inspection is to stand 2 metres from the surface in normal lighting. A torch or high-powered light held against the wall is not the test, because it will show marks on any wall.
Under Resene’s guidance, if stopping or board shows through the surface prep and seal coat, Level 5 has not been achieved. Point that out before the final topcoats go on, when fixing it is still simple.
Our view
Most of the disputes we hear about on plastering are not about skill. They are about an assumption. The owner pictured a flawless wall, the plasterer priced a standard one, and nobody wrote the level down. Our approach is to settle the finish level room by room at the start, alongside paint colour, sheen and lighting, because those four things decide how the wall looks. Level 5 is a team result: the framer, board installer, plasterer and painter all affect it. That is the reason we run all trades under one team with one point of contact, so the person you speak to is the person who has already briefed every trade. For most rooms, Level 4 with a good three-coat paint system is the right and sensible answer. For a feature wall, a ceiling with downlights or a gloss finish, we specify Level 5 from the framing stage and put it in the fixed-fee quote. Rudi
Plastering and painting as part of one renovation
If you are renovating a kitchen, bathroom or whole home in Auckland, the finish level is one of dozens of decisions across plumbing, electrical, building, plastering and painting. We handle the whole job from start to finish, with fixed-fee quotes, licensed trades coordinated by us, building consent handled where it applies, and one point of contact for you. You can see how our packages are structured on our kitchen and bathroom pricing page, or look at the scope of our full home renovation service.

Smaller repairs, such as patch repairs and touch-up painting, are listed on our small jobs page.
FAQ
Is Level 5 always better than Level 4?
No. Level 5 is a different specification for demanding surfaces, not a better version of every wall. For flat or low-sheen paint in ordinary light, Level 4 gives a good result. Level 5 adds cost that you will not see in those rooms.
Can I upgrade from Level 4 to Level 5 after the plasterboard is stopped?
A skim coat can be applied over a Level 4 surface, but Dulux states that this is not equivalent to Level 5. Level 5 needs the tighter framing and back-blocked joints put in from the start. Decide at the design stage, before the board is fixed.
Will Level 5 make my walls perfect?
No. Both GIB and Siniat state that Level 5 minimises surface variations rather than removing them all. Lighter colours, lower sheen and softer lighting help the result. Judge the wall from 2 metres in normal lighting, which is the accepted inspection method.
Do I need Level 5 in a bathroom or kitchen?
Usually not. Most kitchens and bathrooms are fine at Level 4 with a suitable paint. Level 5 is worth considering if you plan semi-gloss or gloss paint, a dark colour, or strong lighting running along a wall or ceiling.
What should I ask for in the quote?
Ask for the finish level written for each area, who sands and cleans up, the paint system, and what happens to defects visible after the first coat of paint. These details make quotes comparable and avoid later disagreement.
Sources
Recommended


Comments