top of page

Balustrade Height in NZ: What the Building Code Requires

Writer: Rudi Visser
Rudi Visser
2 days ago
9 min read

Balustrade along a raised timber deck

For a standard New Zealand house, a balustrade (the safety barrier at the edge of a deck, balcony or stair) must be at least 1000 mm high on decks, balconies and internal floor edges, and at least 900 mm high on stairs, ramps and their landings. Those are the Acceptable Solution F4/AS1 minimums set out in MBIE’s Guidance on Barrier Design. Height is only one part of a compliant barrier. Openings, climbability, strength and consent matter just as much, and this guide covers each in plain terms.



TL;DR

 

  • Detached houses and the private units of multi-unit dwellings: 1000 mm minimum on balconies, decks and floor edges, 900 mm on stairs, ramps and landings.

  • A barrier is required wherever someone could fall 1 metre or more, under Building Code clause F4.

  • Openings must stop a 100 mm sphere passing through, and there should be no footholds between 150 mm and 760 mm above the floor.

  • A stair handrail is a separate item from a barrier: 900 to 1000 mm above the pitch line of the stair.

  • Apartment common areas and non-housing buildings have higher figures, including 1100 mm in most locations.

 

Table of Contents

 

 

When you need a balustrade at all

 

The trigger is the height of the fall, not the type of structure. MBIE explains that Building Code clause F4.3.1 requires a barrier wherever people could fall 1 metre or more from an opening in the external envelope or floor, or from a sudden change of level in or associated with a building.

 

That covers raised decks, upstairs balconies, mezzanine floors, open stairwells and landings. A deck 600 mm off the ground does not need a barrier under the Code. A deck 1.2 metres up does.

 

Consent is a separate question. MBIE’s exempt building work guidance says a deck, platform or boardwalk from which it is not possible to fall more than 1.5 metres, even if it collapses, needs no building consent. A safety barrier is still required under clause F4 once the fall is 1 metre or more. So a 1.2 metre deck can skip consent but still needs a compliant balustrade. Our guide to deck consent in NZ goes through that in more detail.

 

Balustrade height for houses

 

For a detached dwelling, and for the inside of a single household unit within a multi-unit building, the minimums in F4/AS1 Table 1 are:

 

Location

Minimum barrier height

Stairs, ramps and their landings

900 mm

Balconies and decks

1000 mm

Internal floor edges and mezzanines

1000 mm

Those figures come from MBIE’s Guidance on Barrier Design (March 2012). BRANZ gives the same 1.0 m minimum for residential deck barriers where the fall exceeds 1.0 m.

 

The balcony question that people search for has the same answer. A balcony is a raised platform at the edge of a floor, so 1000 mm is the housing minimum. Many builders and designers allow a little extra for the finished surface and top rail, which keeps the barrier above the line once decking or tiles go down.

 

Apartments, common areas and other buildings

 

The rules change outside the private home. In all other buildings, and in the common areas of multi-unit dwellings, the same MBIE guidance sets 900 mm on stairs or ramps, 800 mm within 530 mm of fixed seating, and 1100 mm everywhere else. If you own a unit in an apartment block, the shared balcony or walkway outside your door is likely to fall under the higher figure, and the body corporate usually controls it.


Minimum barrier heights for shared buildings

How to measure the height correctly

 

A barrier measured from the wrong place can fail even when it looks tall enough. The guidance says to measure vertically from the finished floor level on floors, landings and ramps, ignoring carpet or similar coverings. On stairs, measure from the pitch line or the stair nosings.

 

The pitch line is the sloping line joining the front edges of the stair treads. It matters because a barrier beside a stair rises at an angle, and the 900 mm is taken straight up from that line.

 

Two practical points follow:

 

  1. Measure from the final surface. If decking boards, tiles or a membrane are still to be laid, allow for them. A barrier that is 1000 mm from the joists may be 960 mm from the deck surface.

  2. Watch sloping ground. Where a deck sits on a slope, the fall height can be greater than it looks from the house side. Measure the drop at the open edge, not at the door.

 

Height is only part of the rule

 

A tall barrier with the wrong gaps or a ladder-like pattern is still non-compliant. For homes, where young children are expected, the main requirements are these.

 

Openings: the 100 mm sphere

 

No opening in the barrier may let a 100 mm sphere pass through. BRANZ lists this alongside a limit of less than 15 mm gaps between horizontal rails, and no sharp edges or projections. Check the gap at the bottom too, between the lowest rail or glass edge and the deck surface, and the gap on stairs, where the triangle formed by the tread, riser and bottom rail is easy to overlook.

 

Climbability: no footholds from 150 mm to 760 mm

 

In buildings likely to be used by children under six, MBIE’s guidance requires barriers with no easy or obvious means of climbing. There should be no toe-holds between 150 mm and 760 mm above the finished floor, and any ledge in that zone must be 15 mm deep or less unless it slopes 60 degrees below horizontal towards the person standing there.

 

This is why horizontal rails and wires, popular for the look, are a problem on residential decks: a child can use them as a ladder. Vertical balusters are the simplest way to meet the rule.

 

BRANZ also notes the top of the barrier must be at least 760 mm above any fixed seat, such as a built-in bench along the edge. A bench against the barrier effectively lowers the barrier height for anyone standing on it.

 

Strength

 

Barriers must resist imposed loads (people leaning or pushing) and wind loads without collapsing or deflecting unacceptably. BRANZ points to AS/NZS 1170 for those loads. For a proprietary balustrade system, the practical question is whether the manufacturer’s compliance evidence matches your installation and whether the deck or wall behind it can carry the load. A post fixed to a rotten joist is only as strong as the joist.

 

Glass balustrades

 

Glass follows the same height rules as any other infill: 1000 mm on a residential deck or balcony and 900 mm on stairs. The extra care goes into the details.

 

MBIE’s determination 2019-023 looked at a glass balustrade where a 1050 mm panel sat 820 mm above a concrete nib. The panel met the 1000 mm minimum height, but the design failed the climbability clause because a handrail projecting from the inside of the glass gave a place to step or grip. The same determination notes that F4/AS1 allows a nib of any height provided the glass sits no more than 15 mm from the interior edge of the nib, or a 60 degree fillet is used, so the nib cannot become a ledge.


Glass balustrade with projecting handrail

For a homeowner, the lesson is that the whole assembly is judged, not just the glass height. Ask for the glass type, fixing method and compliance evidence in writing before the work starts.

 

Balustrade or handrail: what is the difference?

 

The two terms get mixed up. A barrier stops people falling. A handrail gives you something to hold while you climb or descend. On stairs, you often need both.

 

MBIE’s barriers and handrails page says Acceptable Solution D1/AS1 requires handrails on all stairs, positioned between 900 and 1000 mm above the pitch line. The Code’s durability guidance also uses the words more precisely than everyday speech: a baluster is a post supporting the top and bottom rails, and the balustrade is the infill between them.

 

If your question is about the rail beside a staircase, our guide to handrail height in NZ covers it in full.

 

A worked example

 

Say you are building a deck off a first-floor lounge in an Auckland home, with the finished deck surface 2.4 metres above the lawn.

 

  • Is a barrier needed? Yes. The fall is more than 1 metre.

  • Is consent needed? Yes. The deck is higher than 1.5 metres, so the exemption does not apply.

  • How high? At least 1000 mm above the finished deck surface.

  • Infill? Vertical balusters with gaps under 100 mm, or glass panels with no gap a 100 mm sphere can pass through.

  • Stairs down to the lawn? A 900 mm barrier measured from the stair nosings, plus a handrail at 900 to 1000 mm above the pitch line.

  • Built-in bench at the edge? The top of the barrier must be at least 760 mm above the seat.

 

Working through a list like this before you get quotes means every builder prices the same job.

 

What has changed recently

 

The core F4/AS1 figures for housing have stayed the same for years. MBIE’s amendments page, last updated in January 2026, records an August 2025 version of the Schedule 1 guidance that clarified points without changing Schedule 1, and October 2025 amendments covering roof-mounted solar arrays and some setbacks. Neither alters the balustrade heights above. Because Building Code documents are amended from time to time, confirm the current version with MBIE or your council before you finalise a design.

 

Mistakes that cost homeowners money

 

  • Building to 900 mm on a deck. The stair figure is not the deck figure.

  • Choosing horizontal wires or rails for looks. They create the footholds the Code is trying to remove.

  • Skipping the barrier on a 1.2 metre deck because consent is not needed. The exemption covers consent, not safety.

  • Ignoring the structure. A compliant balustrade on a weak deck edge is not safe.

  • Measuring before the finishes go on. Tiles and decking take height off the barrier.

  • Treating a purchased house as already compliant. First-time buyers should look at old decks and stair barriers during due diligence, since older builds may have been made to earlier standards or without consent.

 

Where we come in

 

A balustrade is rarely a standalone job. It sits on a deck, stair or balcony that may need framing, waterproofing, painting or consent. Our full home renovation service brings the trades together under one team, and we manage the building consent process with one point of contact. Our quotes are fixed-fee, so the barrier, the structure behind it and the finishing sit in one agreed scope.


Sortedhomesolutions

If you want the existing balustrade, deck or stairs assessed as part of a wider repair or renovation, see our renovation and repair services or start from our home page.

 

Our view on balustrades

 

Most balustrade problems we hear about start with a deck or stair that was treated as a small add-on. The height gets decided late, the finishes change the measurement, and nobody owns the consent question.   We would rather see the barrier planned with the structure it fixes to. That means the framing, the waterproofing, the stair and the rail are agreed together, with one fixed-fee scope and one person you speak to. Licensed trades are coordinated by us, so you are not chasing a builder, a glazier and a painter separately.   For a first-time buyer or a homeowner, that is the practical value: you get a barrier that is built to the Code, a clear record of what was agreed, and a consent process handled for you.   Rudi

 

FAQ

 

How high should a balcony balustrade be in NZ?

 

For a house, or inside a single household unit, the F4/AS1 minimum is 1000 mm above the finished floor of the balcony. Shared balconies and walkways in apartment buildings are generally held to 1100 mm. Measure from the final surface, not the structure.

 

How high should a glass balustrade be?

 

Glass follows the same figures as other balustrades: 1000 mm on residential decks and balconies and 900 mm on stairs. The glass must also meet the opening, strength and climbability rules, so a handrail or ledge that gives a foothold can cause a failure even when the height is right.

 

Do I need a balustrade on a low deck?

 

The Building Code requires a barrier where the fall is 1 metre or more. Below that, no barrier is required, although many owners add one for children or older family members. If you do install one, the materials still need to meet the Code’s requirements for hazardous materials.

 

Is a handrail the same as a balustrade?

 

No. A balustrade is a barrier that stops falls. A handrail is for gripping on stairs and sits 900 to 1000 mm above the pitch line. A staircase with an open side often needs both.

 

Do I need consent for a balustrade?

 

The consent question depends on the structure it belongs to. A deck where nobody could fall more than 1.5 metres can be exempt, but anything higher generally needs consent, and the barrier must comply either way. Check with your local council, or ask us to handle it as part of the project.

 

Sources

 

Recommended

 

 
 
 

Comments


bottom of page